Start Pc Power supply short PS_ON# line to the common

Standard ATX power supplies typically have the main power connector P1, additional 12V connectors, as well as peripheral, floppy drive, serial ATA, and PCI Express® receptacles, which we will describe below.

For the operation basics of SMPS PSU see our power supply tutorial. The original ATX systems had 20-pin main connector P1. When PCI Express® bus was introduced, PCIe cards needed up to 75W extra. To provide the additional wattage, the old part has been replaced by a new 24-pin P1. Accordingly, different ATX-style PSU may use different number of power wires: see the pinout diagram to the right. The colors in this chart represent recommended wire colors in the PSU cables. These diagrams reflect the front view. The colors are shown here just for reference (you won’t see them from the front). The P1 uses Molex Housing Mini-Fit Jr. P/N# 39-01-2240 style (old part number was 5557-24R), contacts: 44476-1112. Mating motherboard header is Molex 44206-0007. The old socket was 39-01-2200 and the mating header was 39-29-9202. People often want to know what to do if there is a mismatch.

If you want to do some testing of a stand alone unit, to start it up outside of a PC case you need to short PS_ON# line to the common. Otherwise, only 5V standby voltage will be present

Auxiliary ATX connectors

Also note that many brands such as Apple’s Power Mac, Dell (during certain years), Compaq and HP used proprietary boards with entirely different pin designations- see this for info on some brand name power supplies.

All voltages are referenced to the same common (if you need to measure any voltage, connect the return lead of your voltmeter to any of the COM contacts).

The rated current of the main Molex connector is 6A per contact. This means with the old 20-pin style you can’t get more than 18A from 3.3V and 24A from 5V. That’s why in early 2000’s, some motherboards with 3.3V >18A and 5V >24A (mainly dual CPU AMD systems) used an auxiliary 6-pin power cable. It was removed from ATX12V spec v2.0 in 2003 because extra wires were added to P1. For more information on form factors see our computer PSU tutorial.

When the industry began using voltage regulation modules (VRM) running off 12V2 to energize CPU and other motherboard components, the bulk of the wattage shifted to 12 volt buss. Most of today’s motherboards supply their CPU with a separate 12 volt cable, which has 4 pins for ATX style (sometimes called P4) or 8 or more pins for EPS and non-standard high-power systems. Some PSUs may have three or four 12 volt 4-pin connectors. The p/n for a standard P4 is 39-01-2040 or equivalent.

Serial ATA (SATA) connector pinout

Peripheral power connector goes to disk drives, colling fans, and other smaller devices. There may also be a floppy drive cable.

Note that the wire numbers in Serial Power ATA (SATA) connector are not 1:1. There are three pins for each voltage. One pin from each voltage is used for pre-charge in the backplane. The mating serial plug of ATA devices contains both signal and power segments.

Some units may also have an optional 2×3 socket that can be used for auxiliary functions, such as fan monitoring and control, IEEE-1394 power source, and a remote sense of 3.3 V.

Pin out of PCI Express

PSU over 450W designed for high-end discrete graphics cards normally have additional 2×3 or 2×4 connectors. They supply extra current to graphics that require more than 75 watts total.
The 6-pin PCI Express® receptacle is Molex p/n 0455590

0 0 votes
Article Rating
Notify of
Inline Feedbacks
View all comments

©2023 LocalAd


We're not around right now. But you can send us an email and we'll get back to you, asap.

WordPress Ads
Would love your thoughts, please comment.x

Log in with your credentials


Forgot your details?

Create Account